[nzlug] Vodem aka Huewai E220 - anyone got this working?

[Andrew Bruce]

ohci_hcd 0000:00:03.1: wakeup
usb 3-1: new full speed USB device using ohci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 3-1: reset full speed USB device using ohci_hcd and address 3
  Vendor: HUAWEI    Model: Mass Storage      Rev: 2.31
    Type:   CD-ROM                             ANSI SCSI revision: 02
    scsi 2:0:0:0: Attached scsi generic sg0 type 5
    usb-storage: device scan complete


I also don't get anything when I modprobe usb-serial vendor=0x12d1 
product=0x1003

Output cat /proc/bus/usb/devices:

T:  Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-gentoo ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:03.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-gentoo ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:03.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1003 Rev= 0.00
S:  Manufacturer=HUAWEI Technologies
S:  Product=HUAWEI Mobile
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-gentoo ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:03.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 6
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.18-gentoo ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:03.3
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=256ms



Need anything else?

Andrew



Vik Olliver wrote:
> On Thu, 2006-10-19 at 14:08 +1300, Andrew Bruce wrote:
>   
>> Followed the directions in Vik's post but wvdial says Cannot open 
>> /dev/ttyUSB{0,1,2}: No such device.
>>
>> Any further instructions that may be helpful?
>>
>>     
> What does "dmesg" say when you plug the thing in? Give it a while to
> stabilise before running dmesg.
>
> Vik :v)
> -------8<---------8<---------8<---------8<---------8<---------8<-----
> The more corrupt the state, the more numerous the laws.
>
> - Tacitus, 56-120 A.D.
>
>
>
>
> _______________________________________________
> NZLUG mailing list NZLUG at linux.net.nz
> http://www.linux.net.nz/cgi-bin/mailman/listinfo/nzlug
>
>